
雙組份打膠機如何調整滴膠量?
時間:2024-12-09 來源:http://www.yalais.com/ 發布人:昌盛機械
調整雙組份打膠機的滴膠量主要涉及以下幾個步驟:
Adjusting the dispensing amount of the two-component glue machine mainly involves the following steps:
調整比例泵:雙組份打膠機的比例泵負責控制A、B兩種膠水的混合比例。通過松開比例杠桿上的比例泵鎖緊螺釘,將比例泵內外調整至所需的比例。只有當A膠和B膠的配比達到正常值時,才可進行下面的操作。
Adjust the proportion pump: The proportion pump of the two-component gluing machine is responsible for controlling the mixing ratio of adhesive A and B. Adjust the inside and outside of the proportional pump to the desired ratio by loosening the proportional pump locking screw on the proportional lever. The following operation can only be carried out when the ratio of A glue and B glue reaches the normal value.
調整出膠量:出膠量可以通過氣源處理器控制,逆時針調節,出膠量增加,順時針調節出膠量減小。這里指總出膠量。
Adjust the glue output: The glue output can be controlled by the air source processor. If adjusted counterclockwise, the glue output will increase, and if adjusted clockwise, the glue output will decrease. This refers to the total adhesive output.
調整供膠時間:供液時間可以通過控制器進行調整,范圍從0.001-99.99秒可調,以此來控制滴膠量。

Adjust the glue supply time: The liquid supply time can be adjusted through the controller, ranging from 0.001-99.99 seconds, to control the amount of glue dispensed.
檢查和調整壓力桶輸出氣壓:通過調節兩個壓力桶的輸出氣壓,可以方便地調節各種不同比例的混合膠水,范圍可在1:1至3:1的比例。
Check and adjust the output air pressure of the pressure drum: By adjusting the output air pressure of two pressure drums, it is easy to adjust various proportions of mixed glue, ranging from 1:1 to 3:1.
調整點膠閥氣缸行程:通過調節點膠閥氣缸的不同行程,可以調節滴膠量。
Adjust the stroke of the dispensing valve cylinder: By adjusting the different strokes of the dispensing valve cylinder, the dispensing amount can be adjusted.
設置“行走開始延時”與“出膠延時”:這兩個參數是控制打膠開的膠量的,當之間的差值越大時,打膠開始的膠量越多,反之膠量少,需根據實際需要做適當的調整。
Set "walking start delay" and "dispensing delay": These two parameters are used to control the amount of glue applied. The larger the difference between them, the more glue is applied at the beginning of the dispensing process. Conversely, if the difference is less, appropriate adjustments should be made according to actual needs.
檢查和調整混合螺旋管膠嘴:更換或調整混合螺旋管膠嘴,以適應不同的滴膠量需求。
Check and adjust the mixing spiral tube nozzle: Replace or adjust the mixing spiral tube nozzle to meet different dispensing requirements.
檢查和調整掛環和膠管:確保掛環無變型,無缺失,膠管無破損,膠管接頭螺絲無松動,無硅膠溢出,必要時通知設備人員解決。
Check and adjust the hanging ring and hose: Ensure that the hanging ring is not deformed or missing, the hose is not damaged, the hose joint screws are not loose, and there is no silicone overflow. If necessary, notify the equipment personnel to solve the problem.
以上步驟可以幫助您調整雙組份打膠機的滴膠量,以滿足具體的生產需求。在進行調整時,請確保遵循設備的操作手冊和安全指南,以保證操作的準確性和安全性。
The above steps can help you adjust the dispensing amount of the two-component glue machine to meet specific production needs. When making adjustments, please ensure to follow the equipment's operating manual and safety guidelines to ensure accuracy and safety of the operation.
本文由雙組份打膠機為您提供,我們的網站 http://www.yalais.com我們將以全心全意的熱情為您提供服務,歡迎您的訪問!
This article is provided by a two-component glue machine on our website http://www.yalais.com We will provide you with wholehearted enthusiasm and welcome your visit!
- 中空玻璃打膠機,助您開啟高效生產新時代! 2026/02/19
- 中空玻璃生產線打膠機傳送V帶不平衡?這樣調,傳送平穩不跑偏 2026/02/13
- 中空玻璃生產線打膠難題:壓力夠卻打不滿膠?這樣排查就解決 2026/02/12
- 全自動封膠線實操科普:山東昌盛板壓段,筑牢封膠質量核心防線 2026/02/10
- 中空玻璃生產線實操科普:小玻璃清洗機反轉打滾?這樣解決最省心 2026/02/06
- 全自動封膠線實操科普:白膠泵密封圈這樣換,杜絕漏膠保順暢 2026/02/04
- 雙組份打膠機實操科普:出膠體這樣保養維護,延長壽命保順暢 2026/02/02
- 中空玻璃生產線:清洗機這樣保養,清潔高效更耐用 2026/01/30
- 全自動封膠線實操科普:板壓壓合效果差?四角落差這樣調精準 2026/01/28
- 雙組份打膠機實操科普:黑膠泵過濾這樣清洗,避免堵塞保順暢 2026/01/27

當前位置:



產品分類Product categories
聯系我們Contact us
