中空玻璃生產線90度邊有波浪？生產時常見問題排查指南

　　Is there a wave on the 90 degree edge of the insulated glass production line? Guidelines for troubleshooting common problems during production

　　在中空玻璃生產線的封膠工序中，90度邊出現波浪紋是困擾不少生產企業的常見問題。這看似不起眼的波紋，不僅拉低了中空玻璃的外觀質感，更暗藏質量隱患——可能導致膠層貼合不緊密，直接降低產品密封性能，增加后期滲水、起霧的風險，嚴重時還會影響產品合格率，耽誤生產進度。很多生產線操作人員遇到這類問題時容易盲目排查，反而浪費時間。今天就專門聚焦中空玻璃生產線，給大家梳理封膠線90度邊出波浪的核心原因，方便大家直接對照排查，快速解決問題。

　　In the sealing process of insulated glass production lines, the occurrence of wavy lines on the 90 degree edge is a common problem that troubles many manufacturing enterprises. This seemingly inconspicuous ripple not only lowers the appearance texture of the insulated glass, but also hides quality hazards - it may cause the adhesive layer to not fit tightly, directly reducing the sealing performance of the product, increasing the risk of water leakage and fogging in the later stage, and in severe cases, affecting the product qualification rate and delaying production progress. Many production line operators are prone to blind troubleshooting when encountering such problems, which actually wastes time. Today, we will specifically focus on the production line of insulating glass, and sort out the core reasons for the waves on the 90 degree edge of the sealing line, making it convenient for everyone to directly compare and investigate, and quickly solve problems.

　　第一個核心原因：膠嘴選型或狀態出問題，這是最容易排查的關鍵點。在中空玻璃生產線的封膠環節，膠嘴是直接影響涂膠成型的核心部件。首先要核對膠嘴型號是否匹配當前生產需求，膠嘴口徑太大或太小，都會導致出膠量不均勻，尤其是90度轉角處，膠層無法平穩過渡，很容易形成波浪。其次要檢查膠嘴的使用狀態，長期在生產線上使用后，膠嘴難免會出現磨損、變形，或者被膠水殘渣堵塞，這些都會破壞出膠的順暢性。另外，膠嘴與玻璃的距離調節不當也會引發問題，距離太遠，膠水無法精準貼合玻璃表面；距離太近，又會產生過大阻力，導致涂膠軌跡偏移，最終形成波浪紋。

　　The first core reason is that there is a problem with the selection or condition of the rubber nozzle, which is the easiest key point to troubleshoot. In the sealing process of the insulated glass production line, the glue nozzle is the core component that directly affects the coating and molding. Firstly, it is necessary to verify whether the nozzle model matches the current production requirements. If the nozzle diameter is too large or too small, it can lead to uneven dispensing, especially at 90 degree corners where the adhesive layer cannot transition smoothly and can easily form waves. Secondly, it is necessary to check the usage status of the glue nozzle. After long-term use on the production line, the glue nozzle is inevitably worn, deformed, or blocked by glue residue, which will damage the smoothness of the glue dispensing process. In addition, improper adjustment of the distance between the glue nozzle and the glass can also cause problems. If the distance is too far, the glue cannot accurately adhere to the surface of the glass; If the distance is too close, it will generate excessive resistance, causing the glue trajectory to deviate and ultimately forming wavy patterns.

　　第二個核心原因：涂膠參數設置不當，這是生產線中最易忽視的關鍵因素。封膠線的涂膠速度和壓力是影響成型效果的核心參數，兩者沒匹配好，90度邊出波浪的概率會大幅增加。如果涂膠速度過快，膠水在玻璃表面還沒來得及均勻鋪開，就被膠槍快速拖動，尤其是90度轉角處，膠層尚未成型就發生位移，很容易出現波紋；要是涂膠壓力不穩定，時大時小，會直接導致出膠量忽多忽少，轉角處膠層銜接不暢，厚的地方堆積、薄的地方凹陷，形成明顯的波浪。很多生產線操作人員只關注膠水溫度參數，卻忽略了速度和壓力的適配，這也是常見的踩坑點。

　　The second core reason is improper setting of adhesive parameters, which is the most easily overlooked key factor in the production line. The coating speed and pressure of the sealing line are the core parameters that affect the forming effect. If the two are not matched well, the probability of waves appearing on the 90 degree edge will increase significantly. If the glue application speed is too fast and the glue has not been evenly spread on the glass surface, it will be quickly dragged by the glue gun, especially at the 90 degree corner where the glue layer will shift before it is formed, making it easy to produce ripples; If the adhesive pressure is unstable, sometimes large and sometimes small, it will directly lead to fluctuating adhesive output, poor connection of the adhesive layer at corners, accumulation in thick areas, and depression in thin areas, forming obvious waves. Many production line operators only focus on the temperature parameters of the glue, but neglect the adaptation of speed and pressure, which is also a common pitfall.

　　第三個核心原因：膠水狀態不符合生產要求，直接影響涂膠平整度。封膠用的丁基膠、結構膠等材料，其狀態是中空玻璃生產線封膠質量的基礎保障。如果膠水粘度不合適，太稀會導致涂膠時出現流掛不均的情況，太稠則流動性差，難以在玻璃表面順暢鋪開，這兩種情況在90度轉角處都會明顯顯現出波浪。另外，膠水在儲存或生產線使用過程中，如果操作不當導致內部混入氣泡、雜質，涂膠時這些異物會破壞膠層的平整度，而轉角處膠層受力發生變化，波浪問題會更加突出。建議生產線在使用膠水前，先簡單檢查其外觀和流動性，確認無異常后再投入生產。

　　The third core reason is that the adhesive state does not meet the production requirements, which directly affects the smoothness of the adhesive coating. The state of materials such as butyl rubber and structural adhesive used for sealing is the basic guarantee for the sealing quality of the insulating glass production line. If the viscosity of the glue is not suitable, being too thin can lead to uneven flow when applying the glue, while being too thick can result in poor fluidity and difficulty spreading smoothly on the glass surface. Both situations will show obvious waves at a 90 degree corner. In addition, if the glue is stored or used on the production line improperly, bubbles and impurities may be mixed inside. These foreign objects will damage the flatness of the adhesive layer during coating, and the stress on the adhesive layer at corners will change, making wave problems more prominent. It is recommended that the production line conduct a brief inspection of the appearance and fluidity of the glue before using it, and confirm that there are no abnormalities before putting it into production.

　　第四個核心原因：設備運行精度不足，生產線核心部件狀態影響成型效果。中空玻璃生產線的封膠線屬于精密設備，核心部件的磨損或松動會直接拉低運行精度。比如封膠線的導軌、絲杠出現磨損，或者定位裝置松動，會導致膠槍在移動過程中運行不平穩，尤其是在90度轉角時容易出現偏移、抖動，涂膠軌跡自然就變成了波浪狀。還有玻璃定位環節的問題，如果生產線的玻璃輸送、定位裝置出現偏差，會導致涂膠路徑偏離預設軌跡，90度邊的膠層無法按照標準平整成型，進而出現波浪紋。

　　The fourth core reason is insufficient precision in equipment operation, and the status of core components on the production line affects the molding effect. The sealing line of the insulated glass production line is a precision equipment, and the wear or looseness of the core components will directly lower the operating accuracy. For example, if the guide rail and screw of the sealing line are worn, or if the positioning device is loose, it will cause the glue gun to run unevenly during movement, especially at a 90 degree angle, it is easy to deviate and shake, and the glue coating trajectory will naturally become wavy. There is also an issue with the glass positioning process. If there are deviations in the glass conveying and positioning devices on the production line, it can cause the glue path to deviate from the preset trajectory, and the 90 degree edge of the glue layer cannot be formed smoothly according to the standard, resulting in wavy patterns.

　　第五個核心原因：作業環境溫度影響，這是生產線中的“隱形干擾因素”。環境溫度對膠水性能和涂膠效果的影響很容易被忽視，但卻是導致90度邊出波浪的重要原因之一。如果生產線封膠區域的溫度太低，膠水的流動性會變差，涂膠時無法在玻璃表面順暢鋪開，膠層在轉角處堆積就會形成波浪；要是溫度太高，膠水粘度會下降，涂膠后容易出現流掛現象，同樣會破壞90度邊的成型效果。建議生產線將封膠區域的溫度控制在15-30℃的適宜范圍，同時避免溫度波動過大，減少環境對封膠效果的影響。

　　The fifth core reason is the influence of operating environment temperature, which is a "hidden interference factor" in the production line. The influence of environmental temperature on the performance and coating effect of glue is easily overlooked, but it is one of the important reasons for the occurrence of waves at 90 degrees. If the temperature in the sealing area of the production line is too low, the fluidity of the glue will deteriorate, and it will not be able to spread smoothly on the glass surface when applying glue. The glue layer will accumulate at the corners and form waves; If the temperature is too high, the viscosity of the glue will decrease, and it is easy to cause sagging after coating, which will also damage the forming effect of the 90 degree edge. It is recommended to control the temperature in the sealing area of the production line within a suitable range of 15-30 ℃, while avoiding excessive temperature fluctuations and reducing the impact of the environment on the sealing effect.

　　給生產線操作人員分享一個高效排查順序，不用盲目找問題：第一步優先檢查膠嘴，確認型號匹配、無磨損堵塞，同時調好膠嘴與玻璃的距離；第二步調試涂膠參數，先適當降低涂膠速度，穩定涂膠壓力，觀察轉角成型效果；第三步檢查膠水狀態，查看粘度是否合適、有無氣泡雜質；第四步排查設備運行情況，檢查導軌、定位裝置是否松動磨損，校準玻璃定位精度；最后檢查環境溫度，確保符合作業要求。按這個順序排查，基本能快速定位問題并解決，減少生產線停機時間。

　　Share an efficient troubleshooting sequence with production line operators, without blindly looking for problems: the first step is to prioritize checking the rubber nozzle, confirm that the model matches, there is no wear or blockage, and adjust the distance between the rubber nozzle and the glass; The second step is to debug the glue parameters. First, reduce the glue speed appropriately, stabilize the glue pressure, and observe the corner forming effect; The third step is to check the status of the glue, whether the viscosity is appropriate, and whether there are any bubbles or impurities; The fourth step is to investigate the operation of the equipment, check whether the guide rail and positioning device are loose and worn, and calibrate the glass positioning accuracy; Finally, check the ambient temperature to ensure compliance with the job requirements. By following this sequence of troubleshooting, problems can be quickly identified and resolved, reducing downtime on the production line.

　　總結下來，中空玻璃生產線中，封膠線90度邊出現波浪的核心原因就集中在膠嘴、涂膠參數、膠水、設備、環境這五個方面。對生產企業來說，只要在生產線運行過程中，做好封膠設備的日常維護、規范膠水的儲存和使用、精準設置涂膠參數，就能有效避免這類問題。掌握這些原因和排查方法，能幫助操作人員快速解決故障，保障產品質量穩定。如果排查后仍無法解決，建議聯系封膠線設備廠家的專業技術人員，對生產線設備進行全面校準和檢修。

　　In summary, the core reasons for the occurrence of waves on the 90 degree edge of the sealing line in the production line of insulated glass are concentrated in five aspects: the glue nozzle, glue parameters, glue, equipment, and environment. For production enterprises, as long as they do a good job in the daily maintenance of sealing equipment, standardize the storage and use of glue, and accurately set the glue parameters during the operation of the production line, they can effectively avoid such problems. Mastering these reasons and troubleshooting methods can help operators quickly solve faults and ensure stable product quality. If the problem still cannot be solved after investigation, it is recommended to contact the professional technical personnel of the sealing line equipment manufacturer to conduct comprehensive calibration and maintenance of the production line equipment.

　　本文由  中空玻璃生產線  友情奉獻.更多有關的知識請點擊  http://www.yalais.com/   真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from the insulating glass production line For more related knowledge, please click http://www.yalais.com/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.