
打膠機的打膠速度過快的潛在誤差
時間:2017-11-20 來源:http://www.yalais.com/ 發布人:昌盛機械
1、雙組份打膠機打膠之前注意觀察打膠機的膠頭是否有玻璃參差等異物出現,如果將其摻入密封膠內那么我們的中空玻璃的密封效果肯定就不會有那么好了。
1, before the glue, pay attention to observe the glue head of the glue machine, whether there is glass uneven and other foreign bodies appear, if it is mixed into sealant, then the sealing effect of our insulating glass will certainly not be so good.
2、打開氣泵開關,電源總開關,控制臺開關,在控制臺按手動按鈕,我們將打膠機膠頭讓他回位到原點,這是我們要對打膠機的速度進行下調節(一般情況下使用我們設置好的速度即可),密封不嚴可能是由于打膠機的打膠速度過快而我們的鋁條安裝的時候深淺不一所以導致中空玻璃的密封膠在鋁條深的地方會出現密封不嚴的情況。
2, open the pump switch, power switch, control switch, manual button on the console, we will glue machine glue head let him return to the origin, this is we want to fight the glue machine speed regulation (we use set speed under normal circumstances can), may be sealed and lax the glue machine glue fast and our aluminum strips when installing shades resulting in insulating glass sealant in aluminum deep place will be sealed and lax circumstance.
3、然后是混交了,按桶膠按鈕,按工作選擇按鈕,然后按拍膠啟動,在按伐開,此時膠頭以出膠,等看不見白膠,以混均勻以后按伐關,此時我們就可以進行正常的打膠機工作了。
3, then is mixed, according to the first barrel of plastic button, and then press the select button according to the work, take glue start in cutting, the rubber head to glue, such as invisible glue, to mix well after the press cutting off, we can carry out normal atx-ii work at this time.

4、出現中空玻璃打膠機生產出來的中空玻璃密封不好的另一大主要原因就是我們的鋁條安裝過于隨意~~~盡管我們的設備無需進行設置可全自動的檢測并處理深淺不一的鋁條,但是如果差距太大且打膠速度過快的話也是有可能發生中空玻璃密封不嚴漏氣的情況。
4, hollow glass hollow glass glue machine produced not sealed another major reason is that our aluminum strip is installed too freely while our equipment ~ ~ ~ without setting aluminum automatic detection and processing depth, but if the gap is too large and too fast then glue it may occur hollow glass Mifengbuyan leak case.
5、打膠機的供嬌壓力如果不夠的話也是會出現這個問題的,因為打膠機的膠體完全靠氣壓來擠出設備并完美的涂裝在中空玻璃的鋁條中的。如果壓力過小的話也會導致中空玻璃打膠機密封不嚴
5, if the pressure of the glue machine is not enough, it will also appear this problem, because the glue of the glue machine is completely squeezed by the air pressure equipment, and perfectly painted in the aluminum strip of the insulating glass. If the pressure is too small, it will lead to the sealing of glass sealing machine is not strict
本文的精彩內容來自雙組份打膠機詳細內容請點擊我們的官方網站:http://linshi.jncsjx.com謝謝您的到來
The wonderful content of this article comes from the two component dispenser, please click on our official website: http://linshi.jncsjx.com, thank you for coming
- 中空玻璃打膠機,助您開啟高效生產新時代! 2026/02/19
- 中空玻璃生產線打膠機傳送V帶不平衡?這樣調,傳送平穩不跑偏 2026/02/13
- 中空玻璃生產線打膠難題:壓力夠卻打不滿膠?這樣排查就解決 2026/02/12
- 全自動封膠線實操科普:山東昌盛板壓段,筑牢封膠質量核心防線 2026/02/10
- 中空玻璃生產線實操科普:小玻璃清洗機反轉打滾?這樣解決最省心 2026/02/06
- 全自動封膠線實操科普:白膠泵密封圈這樣換,杜絕漏膠保順暢 2026/02/04
- 雙組份打膠機實操科普:出膠體這樣保養維護,延長壽命保順暢 2026/02/02
- 中空玻璃生產線:清洗機這樣保養,清潔高效更耐用 2026/01/30
- 全自動封膠線實操科普:板壓壓合效果差?四角落差這樣調精準 2026/01/28
- 雙組份打膠機實操科普:黑膠泵過濾這樣清洗,避免堵塞保順暢 2026/01/27

當前位置:



產品分類Product categories
聯系我們Contact us
