中空玻璃全自動封膠機是玻璃深加工設備中產生較晚但用量較大的機械設備之一，主要作用是將半成品的中空玻璃做好密封，也可以作異形玻璃的密封。正確合理的使用中空玻璃自動打膠機，不僅能保證生產的正常進行，還會起到延長機器壽命的作用，下面小編就給大家講一講中空玻璃全自動封膠機的調試的方法和一些注意事項！
Hollow glass automatic sealant machine is one of the mechanical equipments which produce late but consume large amount in glass deep processing equipment. Its main function is to seal semi-finished hollow glass well, and also to seal special-shaped glass. Correct and reasonable use of hollow glass automatic gluing machine can not only ensure the normal production, but also play a role in prolonging the life of the machine.
調試方法：放在一個平整干凈的平面上，連接電源和氣源，兩者確認接通之后就開始進行操作。打開氣泵開關，電源總開關，控制臺開關，在控制臺按手動按鈕，然后在顯示屏上找到原點設定，點擊輔助原點設定，然后點擊頭部原點設定，注意原點設定時避免頭部和輔助吸盤碰撞。等設定好然后返回找到玻璃厚度設定，先是玻璃的厚度然后是鋁隔條然后還是玻璃的厚度，輸入完以后，點擊設置進入。等命令位置和當前位置數值一致即可，注意設置時傳送帶上不要有玻璃。然后是混交了，按桶膠按鈕，按工作選擇按鈕，然后按拍膠啟動，在按伐開，此時膠頭以出膠，等看不見白膠，以混均勻以后按伐關，在按鏈接生產線，自動，自動運行，此時可以自動打膠。
Debugging method: Put it on a flat and clean plane, connect the power supply and the gas source, and then start operation after the two are confirmed to be connected. Firstly, turn on the air pump switch, the main power switch, the console switch, press the manual button on the console, then find the origin setting on the display screen, click the auxiliary origin setting, then click the origin setting on the head, pay attention to avoid the collision between the head and the auxiliary sucker when setting the origin. After setting it, return to find the glass thickness setting, first the glass thickness, then the aluminium partition, then the glass thickness. After input, click Settings to enter. Just wait for the command position to be consistent with the current position value. Be careful not to have glass on the conveyor belt when setting. Then mixing, press the first bucket glue button, press the work selection button, then press the tap glue to start, in the cutting, at this time the glue head to produce glue, etc. can not see the white glue, after mixing evenly, press the cut off, in the link production line, automatic, automatic operation, at this time can automatically glue.

調試的注意事項：
Notes for debugging:
1、在當天機器操作完畢后要把膠管內的膠沖出，防止硬化；如果長時間不實用要注意用煤油清洗膠管和膠槍。
1. After the machine is finished, the glue in the rubber tube should be washed out to prevent hardening. If it is not practical for a long time, we should pay attention to cleaning the rubber tube and gun with kerosene.
2、雙組份打膠機使用的硅酮膠或聚硫膠要注意雜質不能過高，低質量的膠容易堵塞膠管的過濾系統，造成出膠不暢或不均勻。
2. Silicone glue or polysulfide glue used in two-component glue beater should pay attention to the impurities should not be too high, low-quality glue is easy to block the filter system of rubber hose, resulting in poor or uneven glue production.
3、在更換膠的品種時要特別注意把雙組份打膠機內殘留的膠沖凈，好清洗，因為不同品種甚至的膠容易反應堵塞機器。
3. When replacing rubber varieties, special attention should be paid to cleaning the residual rubber in the two-component glue beater, because different varieties or even brands of glue are easy to react and clog the machine.
液壓站系統的壓力，不能調的太高，要根據室內環境溫度等實際情況，調至滿足膠嘴正常出膠均勻打膠即可。打開液壓站時一定要打開膠槍，否則B組份管路壓力將升得很高，造成安全事故。
The pressure of hydraulic station system can not be adjusted too high. According to the actual situation of indoor environment temperature, it can be adjusted to meet the normal tapping of rubber nozzles. When opening the hydraulic station, the rubber gun must be opened, otherwise the pressure of component B pipeline will rise very high, resulting in safety accidents.
以上關于全自動封膠機的一些基本情況就先給大家介紹到這里了如，如果大家還有什么不懂得的地方歡迎大家到我們的官網：http://linshi.jncsjx.com和我們的在線客服人員進行咨詢，相信會給大家一個滿意的答復。謝謝大家的支持！
The above basic information about automatic sealant machine will be introduced to you first. If you don't know anything else, you are welcome to our official website: http://linshi.jncsjx.com and our online customer service staff for consultation, I believe you will have a satisfactory answer. Thank you for your support!