
雙組份打膠機桶的更換步驟您了解嗎?
時間:2020-06-11 來源:http://www.yalais.com/ 發布人:昌盛機械
雙組份打膠機顧名思義,是用于輸送或泵送膠液的設備。雙組份上膠機設備主要用于輸送高粘度的流體介質。今天我們來看看雙組份打膠機桶的更換步驟。
As the name implies, the two-component dispenser is used for conveying or pumping glue liquid. The two-component sizing machine is mainly used to transport high viscosity fluid medium. Today, let's take a look at the replacement procedure of the two-component dispenser barrel.
1. 關閉氣泵的入口壓力。
1. Close the inlet pressure of the air pump.
2. 打開橡膠排泄閥,釋放內部系統的壓力。

2. Open the rubber drain valve to release the pressure of the internal system.
3.打開壓力板吹管閥。
3. Open the pressure plate blow valve.
4. 將升降控制閥旋到“上”位置。
4. Turn the lifting control valve to the "up" position.
5. 壓力板將從膠筒中升起,終與膠筒分離到合適的位置,代替膠筒。
5. The pressure plate will be lifted from the rubber cylinder and finally separated from the rubber cylinder to a suitable position to replace the rubber cylinder.
6. 從設備機架上拆下空膠筒。
6. Remove the empty cartridge from the equipment rack.
7. 關閉壓盤吹管閥。
7. Close the pressure plate blow pipe valve.
8. 清洗壓片的兩個密封圈,使表面清潔。
8. Clean the two sealing rings of the tablet to make the surface clean.
9. 仔細檢查新桶是否有凹痕或其他損壞。不要使用損壞的桶,因為這會損壞壓板。
9. Check the new drum carefully for dents or other damage. Do not use a damaged bucket as this will damage the platen.
10. 將新膠桶置于設備底座中心,壓板下方。
10. Place the new rubber barrel in the center of the equipment base and under the pressing plate.
11. 在閥瓣密封環上涂潤滑脂(諾德森公司:900302)。
11. Apply grease to the disc seal ring (Nordson: 900302).
12. 拆卸排氣和橡膠出口杠桿。
12. Remove the exhaust and rubber outlet levers.
13. 將升降控制閥移至“下”位置,慢慢將壓力板移至開啟的橡膠筒內。將升降控制閥移動到中間“空檔”位置,可停止壓力板的移動。
13. Move the lifting control valve to the "down" position, and slowly move the pressure plate to the open rubber cylinder. Move the lifting control valve to the middle "neutral" position to stop the movement of the pressure plate.
14. 連續壓下壓板。當排氣口和排氣口有穩定的膠流時,將排氣口和排氣口杠桿重新安裝到壓板上,并擰緊壓板在接頭上。
14. Press down the pressing plate continuously. When the exhaust port and exhaust port have stable glue flow, reinstall the exhaust port and exhaust port lever on the pressure plate, and tighten the pressure plate on the joint.
15. 完成換鼓步驟,打開氣泵進氣開關,正常工作。
15. Complete the drum changing step, turn on the air pump intake switch and operate normally.
以上是雙組份打膠機廠家小編為大家介紹的相關內容,想要了解更多內容,歡迎訪問網站:http://linshi.jncsjx.com
The above is the relevant content introduced by the manufacturer of two-component gluing machine. If you want to know more, please visit the website: http://linshi.jncsjx.com
- 中空玻璃打膠機,助您開啟高效生產新時代! 2026/02/19
- 中空玻璃生產線打膠機傳送V帶不平衡?這樣調,傳送平穩不跑偏 2026/02/13
- 中空玻璃生產線打膠難題:壓力夠卻打不滿膠?這樣排查就解決 2026/02/12
- 全自動封膠線實操科普:山東昌盛板壓段,筑牢封膠質量核心防線 2026/02/10
- 中空玻璃生產線實操科普:小玻璃清洗機反轉打滾?這樣解決最省心 2026/02/06
- 全自動封膠線實操科普:白膠泵密封圈這樣換,杜絕漏膠保順暢 2026/02/04
- 雙組份打膠機實操科普:出膠體這樣保養維護,延長壽命保順暢 2026/02/02
- 中空玻璃生產線:清洗機這樣保養,清潔高效更耐用 2026/01/30
- 全自動封膠線實操科普:板壓壓合效果差?四角落差這樣調精準 2026/01/28
- 雙組份打膠機實操科普:黑膠泵過濾這樣清洗,避免堵塞保順暢 2026/01/27

當前位置:



產品分類Product categories
聯系我們Contact us
