雙組份打膠機的留意事項
Notes on Two-Component Glue Punching Machine
1.在當天機器操作終了后要把膠管內的膠沖出，避免硬化；假如長工夫不適用要留意用煤油清洗膠管和膠槍。
1. After the machine operation on that day, the glue in the hose should be washed out to avoid hardening; if long time is not suitable, pay attention to cleaning the hose and gun with kerosene.
2.雙組份打膠機運用的硅酮膠或聚硫膠要留意雜質不能過高，低質量的膠容易梗塞膠管的過濾零碎，形成出膠不暢或不平均。
2. Silicone glue or polysulfide glue used in two-component glue beater should pay attention to the impurities should not be too high, low-quality glue is easy to obstruct the filter fragments of rubber hose, resulting in poor or uneven glue production.
3.在改換膠的種類時要特別留意把雙組份打膠機內殘留的膠沖凈，好清洗，由于不同種類甚至的膠容易反響梗塞機器。
3. When changing the type of glue, special attention should be paid to cleaning the residual glue in the two-component glue beater. It is best to clean it, because different types or even brands of glue are easy to react to the obstruction machine.
4.液壓站零碎的壓力，不能調的太高，要依據室內環境溫度等實踐狀況，調至滿足膠嘴正常出膠平均打膠即可。翻開液壓站時一定要翻開膠槍，否則B組份管路壓力將升得很高，形成平安事故。
4. Hydraulic station piecemeal pressure, can not be adjusted too high, according to the indoor environment temperature and other practical conditions, adjust to meet the normal tapping average glue can be. When turning over the hydraulic station, the rubber gun must be turned over. Otherwise, the pressure of component B pipeline will rise very high, resulting in a safety accident.

5.A膠提膠泵延續任務1分鐘以上沒有供膠中止，闡明管路內有空氣，此時會報警，須翻開泵上管接頭再翻開A膠提膠泵，直到出膠爲止，中止并接好接頭，膠槍會呈現有空氣的嗶嗶爆破聲，空氣排凈就好了。
5.A rubber-lifting pump lasts for more than 1 minute without ceasing to supply rubber. It clarifies that there is air in the pipeline. At this time, the alarm will be given. It is necessary to turn on the upper pipe joint of the pump and turn on the A rubber-lifting pump until the glue is released, stop and connect the joint, the rubber gun will appear the beeping explosion sound of air, and the air will be discharged clean.
6.硅酮膠B 組份遇空氣會結殼，影響泵的正常任務和管路的疏通，因而，停機時B組份膠的一切通道在泄壓后均應封閉，使B組份不得接觸空氣。
6. Silicone gel B component will crust when it meets the air, which will affect the normal task of the pump and the dredging of the pipeline. Therefore, all passages of silicone gel B component should be closed after pressure relief, so that component B can not touch the air.
7.正常任務時不要斷氣源，假如發現斷氣源應中止任務。
7. Do not stop the gas source during normal tasks. If the gas source is found, the task should be terminated.
綜上所述有濟南昌盛機械提供，想了解更多雙組份打膠機知識，歡迎關注我們的網站：http://www.yalais.com謝謝支持！
In summary, all the above-mentioned Jinan Changsheng Machinery provides, want to know more about the two-component glue machine knowledge, welcome to pay attention to our website: http://www.yalais.com Thank you for your support!