現在的玻璃工程越來越普遍，對打膠的要求也是越來越嚴格！于是一種方便快捷，質量可靠的打膠設備出現了--雙組份打膠機！下面小編就給大家介紹一下這種打膠機的使用注意事項！
Now glass engineering is becoming more and more popular, and the requirement of gluing is becoming stricter and stricter. So a convenient, fast and reliable gluing equipment appeared - two-component gluing machine! The following edition will introduce to you the use of this type of glue beater notice points!
1.由于雙組份密封膠的固化需要一定時間，因此，已涂了雙組份密封膠的玻璃應水平輕輕搬動。
1. Since the curing of the two-component sealant takes a certain time, the glass coated with the two-component sealant should be moved horizontally and gently.
2.A組、B組份膠應保持清潔，嚴防異物進入膠中。
2. Group A and B glue should be kept clean and foreign bodies should be strictly prevented from entering the glue.
3.在連續工作過程中，膠槍每次停止工作時間一般不得超過20分鐘，否則，應用A組份膠沖出全部混合膠，直至單一的A組份膠從槍口排出為止。
3. In the continuous working process, the rubber gun should not stop working for more than 20 minutes at a time. Otherwise, the whole mixture should be produced by using component A glue until a single component A glue is discharged from the muzzle of the gun.
4.高壓膠管不得強行擠壓、彎曲，防止影響系統正常工作。
4. High-pressure hose shall not be forced to extrude or bend to prevent the normal operation of the system.

5.混膠器應經常保持暢通，以保證良好的出膠效果。如遇堵塞情況，可用丙酮浸泡后清洗。建議每5組清洗一次。
5. Mixers should be kept unblocked regularly to ensure good gumming effect. In case of blockage, it can be soaked in acetone and cleaned. It is recommended to clean every 5 groups.
6.當膠槍長時間不用時（超過一周），應拆下槍體使用溶劑將膠槍和混膠器內的殘留膠體清洗干凈。
6. When the rubber gun is not used for a long time (more than a week), the gun body should be removed and the residual colloid in the rubber gun and mixer should be cleaned with solvent.
7.不同雙組份膠生產廠家所生產的膠內含雜質數量不同，根據實際情況清晰B組分的過濾網及單向止回閥，建議每?jī)山M清洗一次。
7. The amount of impurities in the glue produced by different two-component glue manufacturers is different. According to the actual situation, the filter screen and check valve with clear B component are recommended to be cleaned once for each two groups.
8.任何因膠體固化所造成的膠槍、管路或整機的故障，一律不在保修范圍之內。
8. Any malfunction of rubber gun, pipeline or whole machine caused by gel solidification is not covered by warranty.
9.定期給各泵的加油口加油，應保證油霧器內不斷油。
9. Regular refueling at the refuelling port of each pump should ensure continuous oil in the oil mist.
好了，今天的內容就暫且給大家介紹到這里了！以上的精彩內容由雙組份打膠機的小編整理提供，更多的精彩內容請繼續關注我們，我們會定期發布更多的精彩內容，請記住我們的官網：http://www.yalais.com
Okay, today's content will be introduced to you here for the time being! The above wonderful content is provided by the small edition of two-component glue machine. More wonderful content please continue to pay attention to us. We will release more wonderful content regularly. Please remember our official website: http://www.yalais.com.