雙組份上膠機控制系統采用PLC和觸摸屏，人機界面，一鍵操作。該設備操作簡單，使用方便。伺服控制系統選用世界名牌(日本安川)，功能更穩定。滿足設備運行要求，玻璃污染可忽略不計。只需一人操作設備即可完成整塊玻璃的上膠。穩定可靠，生產效率高。雙組份涂膠機由A、B膠泵、氣動系統、升降結構、機架等組成。那么在使用雙組份膠機時注意什么問題呢?讓我們來了解一下。
　　The control system of two-component gluing machine adopts PLC and touch screen, human-machine interface and one key operation. The device is easy to operate and use. The servo control system adopts the world famous brand (Yaskawa, Japan), with more stable function. Meet the operation requirements of the equipment, and the glass pollution can be ignored. It only needs one person to operate the equipment to complete the gluing of the whole glass. Stable and reliable, high production efficiency. The two-component glue applicator consists of a and B glue pumps, pneumatic system, lifting structure, frame, etc. So what should we pay attention to when using the two-component glue machine? Let's understand.
　　1. 由于雙組份制膠機的固化需要一定的時間，所以涂有雙組份密封劑的玻璃需要水平移動。
　　1. Since the curing of the two-component glue making machine takes a certain time, the glass coated with the two-component sealant needs to move horizontally.
　　2. A組和B組的膠要保持清潔，嚴禁異物進入膠內。

　　2. The glue of group A and group B shall be kept clean and no foreign matters are allowed to enter into the glue.
　　3.連續運行過程中，膠槍停止時間不超過20分鐘。否則，應使用膠水的組成部分沖洗所有混合的膠水，直到一個單一的組成部分的膠水從槍口排出。
　　3. During continuous operation, the stop time of glue gun shall not exceed 20 minutes. Otherwise, all mixed glue should be rinsed with a component of glue until a single component of glue is discharged from the muzzle.
　　4. 不得強行擠壓或彎曲高壓軟管，以免影響系統的正常運行。
　　4. Do not squeeze or bend the high-pressure hose forcibly to avoid affecting the normal operation of the system.
　　5. 混合器應始終保持暢通，以確保良好的粘合劑效果。若堵塞，浸泡后用丙酮沖洗。建議每5套洗一次。
　　5. The mixer shall be kept smooth at all times to ensure good adhesive effect. If clogged, wash with acetone after soaking. It is recommended to wash every 5 sets.
　　6. 當膠槍長時間不使用(超過一周)時，應將膠槍本體取出，用溶劑清洗膠槍和混合器內殘留的凝膠。
　　6. when the rubber gun is not used for long time (over a week), the rubber gun body should be removed and the residual gel in the rubber gun and mixer should be cleaned with solvent.
　　7. 不同雙組分打漿機生產的膠中雜質的含量不同。根據實際情況，B組件的濾網和單向止回閥每兩組清洗一次。
　　7. The content of impurities in the rubber produced by different two-component beaters is different. According to the actual situation, the filter screen and check valve of B assembly shall be cleaned once every two groups.
　　8. 由于膠槍、管道或機器的膠態固化而造成的任何缺陷都不在保修范圍內。
　　8. Any defects caused by the glue curing of glue gun, pipe or machine are not covered by the warranty.
　　9. 定期向雙組份打漿機各泵的加油口加注油，保證油在霧化器內持續存在。
　　9. Regularly add oil to the oil filler of each pump of the two-component beater to ensure the continuous existence of oil in the atomizer.
　　以上就是對雙組份打膠機注意事項的詳細介紹，想要了解更多請點擊官網http://www.yalais.com
　　The above is a detailed introduction to the precautions of the two-component dispenser. For more information, please click http://www.yalais.com