如果在操作膠水機時出現氣泡，那么一定有一些問題此時無法繼續工作，但應該先解決這些問題，否則氣泡過多會影響產品的生產質量。當雙組分膠水灌裝機運行時，產生氣泡的原因更多。然后，作為一個操作員，我們應該分析并看看是什么導致了泡沫，然后解決這些情況。今天，讓我們簡單地向您介紹泡沫的原因和解決方案。
If bubbles occur during the operation of the glue machine, there must be some problems that cannot continue to work at this time, but these problems should be solved first, otherwise too many bubbles will affect the production quality of the product. When the two-component glue filling machine is running, there are more reasons for bubbles. Then, as an operator, we should analyze and see what causes the foam, and then solve these problems. Today, let's briefly introduce the causes and solutions of foam.
如果使用雙組分膠水灌裝機時產生氣泡，您可以考慮是否將氣泡帶入操作過程。例如，在混合時，如果只在一個方向攪拌，很容易導致混合不均勻，并且可能會有氣泡。所以這是由混合不良引起的。這會減少氣泡的影響。
If bubbles occur when using the two-component glue filling machine, you can consider whether to bring bubbles into the operation process. For example, when mixing, if mixing in only one direction, it is easy to cause uneven mixing, and there may be bubbles. So this is caused by poor mixing. This will reduce the impact of bubbles.

此外，可能存在產生氣泡的情況，即有一些需要使用氣壓的膠水灌裝機。如果氣壓合理，例如漏氣，此時可能會爆出氣泡。在這種情況下，需要檢查燃氣管道，如果管道出現問題，則需要修理或更換。其次是溫度，這也可能導致氣泡。某些類型的膠水需要在一定的溫度范圍內使用。如果它不在這個溫度范圍內，它可能會讓一些空氣進入。
In addition, there may be bubbles, that is, there are some glue filling machines that need to use air pressure. If the air pressure is reasonable, such as air leakage, bubbles may burst at this time. In this case, it is necessary to check the gas pipeline. If the pipeline has problems, it needs to be repaired or replaced. The second is temperature, which may also cause bubbles. Some types of glue need to be used within a certain temperature range. If it is not in this temperature range, it may allow some air to enter.
簡單介紹雙組分膠水機產生氣泡的原因及解決方法。由于不同的原因，不同類型的膠水可能會產生氣泡。例如，一些膠水可能粘度過大，內部氣體無法正常排出。因此，需要使用一些化學試劑來減少幾年的涂層，然后投入使用，這樣才能有效地避免氣泡。
This paper briefly introduces the causes and solutions of bubbles in the two-component glue machine. For different reasons, different types of glue may produce bubbles. For example, some glue may be too viscous and the internal gas cannot be discharged normally. Therefore, it is necessary to use some chemical reagents to reduce the coating for several years, and then put it into use, so as to effectively avoid bubbles.
當我們在膠水操作中遇到氣泡時，我們應該停下來分析氣泡的根本原因，并注意在日常工作中積累一些經驗。然后，隨著時間的使用越來越長，我們可以通過經驗找到處理這種情況的好方法。例如，在填充膠時，我們經常使用樹脂，樹脂通常會在填充膠的時候添加固化劑，但如果固化劑的比例出現問題，很可能會導致內部產生氣泡。
When we encounter bubbles in glue operation, we should stop to analyze the root cause of bubbles and pay attention to accumulate some experience in daily work. Then, as time goes by, we can find a good way to deal with this situation through experience. For example, when filling rubber, we often use resin. The resin usually adds curing agent when filling rubber, but if the proportion of curing agent is wrong, it is likely to cause bubbles inside.
以上就是為大家介紹的有關雙組份打膠機詳細的介紹,希望對您有所幫助.如果您有什么疑問的話,歡迎聯系我們.我們將以的態度,為您提供服務http://www.yalais.com
The above is a detailed introduction to the two-component sealant applicator 82. I hope it can help you. If you have any questions, please contact us. We will provide you with our service http://www.yalais.com