中空玻璃生產線光電開關小難題：感應不到磨砂玻璃？這樣調就管用

　　Small problem with photoelectric switch in insulated glass production line: unable to sense frosted glass? This adjustment works

　　在中空玻璃生產線中，光電開關就像“眼睛”一樣，負責精準檢測玻璃的位置，保障送料、合片、打膠等環節的有序銜接。但不少一線師傅都遇到過一個棘手問題：光電開關對磨砂玻璃感應不靈敏，甚至完全沒反應，直接導致設備停擺、生產卡頓。其實這不是設備故障，只要掌握正確的接線規范和調節方法，就能輕松解決。今天就專門科普中空玻璃生產線光電開關的實用知識，重點說說感應磨砂玻璃的調試技巧。

　　In the production line of insulating glass, the photoelectric switch is like an "eye", responsible for accurately detecting the position of the glass, ensuring the orderly connection of feeding, laminating, gluing and other links. But many frontline workers have encountered a tricky problem: the photoelectric switch is not sensitive to frosted glass, and even has no response at all, directly leading to equipment shutdown and production lag. Actually, this is not a device malfunction. As long as you master the correct wiring specifications and adjustment methods, it can be easily solved. Today, we will specifically popularize the practical knowledge of photoelectric switches in insulated glass production lines, with a focus on the debugging techniques of induction frosted glass.

　　先跟大家理清基礎：咱們中空線上用的光電開關，常規接三根線就夠用，接線是否規范直接影響感應效果，這是調試的前提。具體接線規則很明確：棕色線是正極，要對應接到信號電箱里的24V接口；藍色線是負極，對應信號電箱的0V接口；黑色線是信號線，連接到電箱內標注“X某某某”的對應接口。實操中建議先確認接線無誤，很多時候感應失靈不是調節問題，而是接線接錯或松動導致的。

　　First, let me clarify the basics for everyone: the photoelectric switch used on our overhead line is usually connected with three wires, and whether the wiring is standardized directly affects the sensing effect, which is a prerequisite for debugging. The specific wiring rules are very clear: the brown wire is the positive pole and should be connected to the 24V interface in the signal box; The blue line is the negative pole, corresponding to the 0V interface of the signal box; The black wire is the signal wire, connected to the corresponding interface labeled 'X' inside the electrical box. In practical operation, it is recommended to first confirm that the wiring is correct. Often, induction failure is not due to adjustment issues, but rather caused by incorrect or loose wiring.

　　解決了接線問題，再來說核心的調節方法——針對感應不到磨砂玻璃的情況，關鍵就是調節光電開關上的調節按鈕。不過要注意，咱們?cè)O(shè)備的光電開關大多藏在版面內部，平時看不到調節按鈕，需要先把光電開關拆下來再操作，拆的時候注意做好部件收納，避免螺絲丟失。

　　After solving the wiring problem, let's talk about the core adjustment method - for situations where frosted glass cannot be sensed, the key is to adjust the adjustment button on the photoelectric switch. However, it should be noted that the photoelectric switches of our equipment are mostly hidden inside the layout, and the adjustment buttons cannot be seen normally. Therefore, it is necessary to remove the photoelectric switches before operation. When removing them, pay attention to organizing the components properly to avoid losing screws.

　　調節的標準很簡單，兩步就能確認：第一步，把需要檢測的磨砂玻璃放到指定位置，然后慢慢旋轉調節按鈕；第二步，觀察光電開關上的指示燈，當指示燈亮起時，就說明調節到位了。如果想更精準，還可以同步查看設備的觸摸屏，確認對應的輸入信號是否正常顯示——指示燈亮且觸摸屏有信號，就代表光電開關已經能穩定感應磨砂玻璃了。

　　The standard for adjustment is very simple, it can be confirmed in two steps: first, place the frosted glass that needs to be tested in the designated position, and then slowly rotate the adjustment button; Step two, observe the indicator light on the photoelectric switch. When the indicator light is on, it means that the adjustment is in place. If you want to be more precise, you can also synchronously check the touch screen of the device to confirm whether the corresponding input signal is displayed normally - if the indicator light is on and there is a signal on the touch screen, it means that the photoelectric switch can stably sense the frosted glass.

　　這里給大家補充幾個實操小提醒：一是拆光電開關時要輕拿輕放，避免碰撞損壞內部元件；二是調節按鈕時幅度要小，慢慢旋轉觀察指示燈，不要一次性擰到底，防止調節過度反而影響感應穩定性；三是調節完成后，把光電開關裝回原位時要固定牢固，避免設備運行中因振動導致位置偏移，再次出現感應問題。

　　Here are a few practical tips for everyone: First, when dismantling the photoelectric switch, handle it gently to avoid collision and damage to internal components; Secondly, when adjusting the button, the amplitude should be small. Slowly rotate and observe the indicator light, and do not twist it all at once to prevent excessive adjustment from affecting the sensing stability; Thirdly, after the adjustment is completed, the photoelectric switch should be firmly fixed back to its original position to avoid position deviation caused by vibration during equipment operation, which may lead to induction problems again.

　　另外，日常使用中還有兩個小技巧能減少感應故障：一是定期檢查光電開關的鏡頭，磨砂玻璃生產過程中容易產生粉塵，鏡頭沾灰會影響感應，定期用干凈的布擦拭干凈即可；二是如果經常需要切換檢測普通玻璃和磨砂玻璃，建議做好調節參數記錄，后續切換時能快速調試到位，節省時間。

　　In addition, there are two tips in daily use to reduce sensing faults: first, regularly check the lens of the photoelectric switch. Dust is easily generated during the production process of frosted glass, and lens dust can affect sensing. Regularly wipe it clean with a clean cloth; Secondly, if it is necessary to frequently switch between detecting ordinary glass and frosted glass, it is recommended to keep a record of the adjustment parameters, so that the subsequent switching can be quickly adjusted to save time.

　　光電開關雖小，卻是中空玻璃生產線穩定運行的關鍵部件，感應不到磨砂玻璃的問題看似棘手，實則只要做好接線規范和精準調節就能解決。對一線操作人員來說，掌握這些基礎調試技巧，能快速應對生產中的小卡頓，減少生產線停擺時間。希望這次科普能幫到大家，在日常操作中更好地應對光電開關的各類小問題。如果遇到其他感應故障，也可以先從接線和清潔鏡頭入手排查，或咨詢?cè)O(shè)備廠家的技術支持。

　　Although the photoelectric switch is small, it is a key component for the stable operation of the insulated glass production line. The problem of not sensing frosted glass may seem tricky, but in fact, it can be solved as long as the wiring specifications and precise adjustments are done properly. For frontline operators, mastering these basic debugging skills can quickly respond to small lags in production and reduce downtime on the production line. I hope this science popularization can help everyone better deal with various small problems of photoelectric switches in daily operation. If you encounter other induction faults, you can also start troubleshooting by wiring and cleaning the lens, or consult the technical support of the equipment manufacturer.

　　本文由  中空玻璃生產線 友情奉獻.更多有關的知識請點擊  http://www.yalais.com/   真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from the insulating glass production line For more related knowledge, please click http://www.yalais.com/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.